MODIFIERS:

  • 16X ROTARY POTS
  • 2X SLIDER POTS
  • 16X MINI PUSHBUTTONS
  • 16 LEDS
  • 4X ARCADE PUSHBUTTONS
  • TOP SPINNER + TOUCH SENSOR
  • SIDE SPINNER + TOUCH SENSOR
  • PAGE SWTCH

EXPANSIONS:

  • DMX OUTPUT
  • DITANCE SENSOR + ACTIVATION SWITCH
  • PADS INPUT – OVER STEREO JACK CONNECTOR
  • MIDI IN/OUT – OVER DIN CONNECTORS
  • CUSTOMIZED LOGOs

PUSHBUTTONS

  • Selectable BUTTON MODE
    • MOMENTARY
    • TOGGLE and TOGGLE GROUPS
  • LED INDICATORS
    • Buttons status report – useful for toggle mode
    • Special light effects.
    • MIDI light feedback – LEDs react to incoming signals.
    • Spinners, pots and distance sensor actions will produce a special light feedback.
  • BUTTONBOARD
    • All the mini buttons are housed on a beautiful controlboard with backlight and mirror finish

TOP and SIDE SPINNERs

  • MECHANICAL ISOLATION
    • The encoders are protected from excessive force for best durability.
  • TOUCH SENSORS
    • The metal parts of the spinners are touch sensitive.
    • Selectable sensitivity.
  • ENDLESS MODE 
    • 0-127 MODE.
    • 63-65 MODE (more detail)
  • POT EMULATION MODE
    • Spinners can emulate a potentiometer, ranging from a MIN to a MAX value.
    • Selectable speed with reverse-action available (negative speed)
  • TOUCH STOP FUNCTION
    • it stops MIDI signals to flow out when the Touch-condition is OFF.
    • this function improves precision, preventing inertial movements from being translated into MIDI signals.
    • It is possible to control two parameters, depending on the Touch_condition.
  • TOUCH RESET FUNCTION
    • designed for PITCH BEND emulation
    • The MIDI signal value will be reset to an origin_value, on Touch_release.
    • Selectable origin_value
  • VIRTUAL TOUCH FUNCTION
    • An ON/OFF MIDI signal is generated when the spinner starts or stops to rotate.
  • SCALE PLAY/LEARN MODE
    • It is possible to specify a note scale that can be played by the Spinner action: glissato sequence will be generated turning the Spinner wheel.
    • a note scale can be recorded when the Touch-condition is ON.


CUSTOMIZED LOGOs


POTENTIOMETERS

  • SELECTABLE MIN AND MAX
  • SELECTABLE CURVES

CONNECTORS

  • DMX OUT
    • With optical and galvanic isolation for safe operation.
    • MIDI2DMX conversion. Incoming MIDI signals will be converted to the corresponding DMX signals.
  • USB MIDI
    • Dart devices are recognized as PNP MIDI devices – no driver needed
  • USB POWERING
    • A 9V DC can however be used for standalone operation.
  • DIN CONNECTORS
    • can be connected with classic MIDI cables
  • PADS INPUT
    • PIEZO SENSORS OR COMMON DRUM PADS CAN BE USED

Un post condiviso da BiTT Projects (@bitt.projects) in data:


DISTANCE SENSOR

 

  • POT MODE.
    • Gliding action from MIN to MAX.
  • BUTTON MODE
    • ON-OFF action. The measured distance will be reported as MIDI Velocity value
  • SCALE PLAY MODE
    • Play stunning glissato effects on a fixed scale or Learn scale.
    • Selectable note range
  • OPERATING DISTANCE RANGE : 50CM
  • ACTIVATION SWITCH
    • It will prevent unwanted MIDI activity to be produced.

Un post condiviso da BiTT Projects (@bitt.projects) in data:


 

 

PAGE SWITCH

  • PAGE SWITCH
    • A SIMPLE 2 POSITIONS SWITCH TO SELECT THE PRESET PAGE
    • SENDS A MIDI SIGNAL ITSELF
    • USEFUL FOR DJ USE

BELOW VIEW

  • BOTTOM SIDE
    • THE ARDUINO BOARD CAN BE EASILY REPLACED WITH MORE POWERFUL ONES FOR FUTURE UPDATES.

DART – machine setup

 

  • Open the DART_EDITOR
  • Load the preset DART_ONE_default_preset.csv
  • Customize your preset, UPLOAD it and SAVE it.

CONFIG TIPS

EDITOR main guide.

EDITOR basics

Page switch

Encoders

Touchsensors

Distance sensor

HID emulation

DMX output

PADS

Joystick / mouse